16
Oct
The clockwise rotation and impression of the swaging head into the copper with this method is more precise and generally yields better results than the punch swage. This is a basic video showing how to use tube expanders for expandingswaging copper pipe followed by brazing copper together.
Shop for Swaging Tools at Ferguson.
How to swage copper pipe. This video is a step-by-step swaging tutorial on how to swage the end of a copper pipe to connect pipework instead of using a coupling. This method is a much easier way to swage of course. Simply set up your pipe in the block and change out the flaring head with the appropriate swaging head.
The clockwise rotation and impression of the swaging head into the copper with this method is more precise and generally yields better results than the punch swage. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Procedure of Swag Copper Pipe Joint.
Prior to the start of the pipe jointing work wear necessary PPE ie. Safety shoes gloves and safety goggles. Prepare tube cutter reamer sand cloth brush flaring block swaging tool and hammer.
Cut the tube to the specified desired length. This is a basic video showing how to use tube expanders for expandingswaging copper pipe followed by brazing copper together. Please like and subscribe for.
Swaging is the process of joining two pieces of copper tubing of the same diameter by expanding or stretching the end of one piece to fit over the other so that joint may be soldered or brazed. As a general rule the length of the joint that fits over the. To perform the swage on copper tubing simply attach the corresponding SPIN Tool size to a drill.
Because they perform their job using high-temperature and friction no clamping tools or. To flare the pipe put it into a hole that has a matching size as the copper on the flare form. Place the reamer on top of the flare form so the conical point is.
Shaping metal materials such as copper tubing through cold working as in the traditional processes of flaring and swaging used in HVAC usually causes the hardening phenomenon which are the main cause for micro cracks and leaks. The SPIN Tools use high temperature through friction to expand the tubing completely avoiding the hardening. The taper and wider section of the swaging tool will stretch the pipe and thus make a very small reduction in wall thickness.
As noted above annealing means heating the pipe to red hot then quenching it or allowing it to cool naturally. This softens the copper and makes swaging easier. You dont swage while hot.
Fit the head into the end of the tube and gradually squeeze the handles. Release when the end of the tube is fully swaged. Learning how to use a swaging tool or a flaring tool is effective for shaping a relatively.
Secure tubing in the flaring block. The tube should extend from the block a distance equal to the diameter of the tube plus one-eighth of an inch. Insert the swaging tool into the end of the tube.
Strike the swaging tool with a hammer until the proper. 38 is soft if it is new. I would swedge both ends of it and then bend it a bit and slip it over the old pipe and weld it.
Be VERY VERY careful you do not start the wall and house on fire. Put some sheet metal there and have a bucket of water and a fire extinguisher nearby. Reduces number of brazes by up to half.
The Reftekk Swage Expander when used in conjunction with bendable quality copper tubing allows each joint to be sealed with only a single braze rather than two brazes associated with conventionally brazed fittings. This reduces labor and the cost of brazing material while significantly reducing leak potential in the system. Secure the pipe into the clamp.
Center the flaring cone over it and slowly tighten it down until a flare is formed. Remember to place the nut on the tubing before flaring it. To avoid splitting the copper do not overtighten.
To swage a pipe replace the flaring bit with the swaging bit. How to CORRECTLY Braze SILVER SOLDER a Copper Pipe. So today Ill be explaining to you how to correctly braze a copper joint.
There are 3 easy steps to getting this accomplishedThe first step is to prepare the joint. Skipping this step may result in an improperly brazed jointStep 2 is the actual b. For example you can have circular tubing or pipe and swage it so the ID is square or even hexagonal.
This means there are even more options and a better chance of catering for your needs. There are two options if you do want to swage a section. The first is to use a dedicated tapered die that is the right size to fit into the end and then widen it.
Properly installed Aluminum and Copper duplex sleeves have been used successfully to suspend overhead equipment in various industries such as stage rigging agriculture marine and construction for many years. It is imperative to follow the manufacturers swaging procedures and verify the swage with a GoNo-Go gauge prior to use. The Swaging Spin Tools allows you to connect tubes with ease and without the use of extra fittings.
Sleeves and unions turning potential waste into actual profit. To top that you can swages with the Swage SPIN Tools in just 5 seconds. To perform the swage on copperaluminumtubing simply attach the corresponding SPIN Tool size to a drill.
Shop for Swaging Tools at Ferguson. Ferguson is the 1 US plumbing supply company and a top distributor of HVAC parts waterworks supplies and MRO products.